Brushless Motor Electronic Speed Controllers

XP-3A | 6A | XC-6A Fwd/Rev | XP-7A | 10A | XP/XC Prog Card


XP-3A 1 Cell 3A Brushless ESC
(Top | 6A | XC-6A Fwd/Rev | XP-7A | 10A | XP/XC Prog Card)

Supplied in standard form as a bare board with signal and motor connectors, but without leads. Also available with JST-SH and AR6400 signal leads and 'UM' or JST-PH battery connectors. The JST-SH lead is suitable for use with the DT Rx33 receiver.

Signal leads are 100mm long and power leads are 50mm long, please contact us if you need longer leads or you require a lead variation that is not listed.

Programming via the tx throttle stick is possible (see the user manual) but tricky when used with as the AR64xx uses high throttle for its own programming. Our info sheet on using an external ESC with AR6400 describes a technique for programming from the tx. A programming card is also available.

Weight (without connectors):1 g
Max Continuous Current:3 A
Size:13 x 11 x 8 mm


Please select signal and battery lead options from the menus below. The 'no lead' options include connectors for you to fit your own leads. Selecting any signal connector option will include bare ended 100mm red/black power wires if you select the 'no lead' battery option.:
Signal Lead:
Battery Lead:

There are currently 0 options selected. Click deselect to cancel all option selections.

Base Price: £ 10.80 Total Price: £ 10.80

Budget 6A Brushless ESC
(Top | XP-3A | XC-6A Fwd/Rev | XP-7A | 10A | XP/XC Prog Card)

Supplied with bare power/motor leads and JR/Hitec signal connector

Weight (without connectors):6 g
Max Continuous Current:6 A
Max BEC Output:0.8A at 5V
Size:32 x 12 x 6 mm

£ 9.90

Also available fitted with a JST-ZH signal connector and a red JST battery connector £ 11.70

.


XC-6A Reversible 6A Brushless ESC
(Top | XP-3A | 6A | XP-7A | 10A | XP/XC Prog Card)

A 1S or 2S (3V-9V) fwd/rev brushless ESC suitable for cars or boats. Fully programmable for LVC, brake, acceleration, timing and neutral 'dead zone'.

Supplied in standard form with bare power/motor leads and JR/Hitec signal connector. Also available with JST-ZH, Molex 1.25mm and JST-SH signal leads and with JST Red or JST-PH battery connector. Please contact us if you require a lead variation that is not listed.

The default operating mode is conditional bidirectional: the ESC will run the motor in reverse only from stop; if reverse stick is selected with the motor still running foward then brake is applied, the stick must be moved to off and then back to the reverse position for the motor to run in reverse. The operating mode and all other programmable features can be changed using the programming card. Instructions may be downloaded here.


Please select signal and battery lead options from the menus below.:
Signal Lead:
Battery Lead:

There are currently 0 options selected. Click deselect to cancel all option selections.

Base Price: £ 12.00 Total Price: £ 12.00

XP-7A 1 or 2 Cell 7A Brushless ESC
(Top | XP-3A | 6A | XC-6A Fwd/Rev | 10A | XP/XC Prog Card)

Supplied in standard form with bare power/motor leads and JR/Hitec signal connector. Also available with JST-ZH, Molex 1.25mm, JST-SH and AR6400 1S and 2S signal leads, the latter includes a diode in the positive wire to drop the 5V BEC output to 4.3V as the maximum working voltage of the AR6400 is 4.5V. Replacement signal leads are 100mm long, please contact us if you need longer leads or you require a lead variation that is not listed.

Programming via the tx throttle stick is possible (see the user manual) but tricky when used with a AR64xx as this uses high throttle for its own programming. Our info sheet on using an external ESC with AR6400 describes a technique for programming from the tx. A programming card is also available.

Weight (without connectors):5 g
Max Continuous Current:7 A
Max BEC Output:1A at 5V
Size:22 x 12 x 5 mm

If you want an XP-7A in standard form, then select the first item in the 'lead type' menu below. All other menu items are for signal lead and/or battery connector options that Micron provides. All 'AR6400 2S options' include a silcon diode in the positive signal wire to drop the 5V BEC to approx 4.3V - this should be used for all AR64xx variants (e.g. AR6410L). Please contact us if the menu does not contain a lead or connector option that matches your need.

Select lead type:

Although the 'UM' power connector option for the AR6400 1S lead is often requested, care is required when using this as the socket is not capable of carrying more than 1.5A-2A continuously.


Budget 10A Brushless ESC
(Top | XP-3A | 6A | XC-6A Fwd/Rev | XP-7A | XP/XC Prog Card)

Supplied with bare power/motor leads and JR/Hitec signal connector

Weight (without connectors):9 g
Max Continuous Current:10 A
Max BEC Output:1A at 5V
Size:27 x 17 x 6 mm

£ 10.80

Programming Card for XP/XC Series ESC
(Top | XP-3A | 6A | XC-6A Fwd/Rev | XP-7A | 10A)

A programming card for XP and XC series ESC. The ESC receiver lead is plugged into the card. A 4 digit LED display allows parameter values to be viewed or changed.

This card can be used for programming the xp-3a, xp-7a and xc-6a ESC. A scan of the instruction sheet is available here (I apologise for the low quality of the scan).

The programming card has a JR/Hitec 0.1" pitch connector so an adapter lead will be required if your ESC has a different plug - JR/Hitec plug at one end and a socket to match your ESC at the other. A special adapter cable is available for the XP-3A; this has the XP-3A 3 pin socket and a 'UM', red JST or JST-PH battery socket.

Adapter Lead:

There are currently 0 options selected. Click deselect to cancel all option selections.

Base Price: £ 7.95 Total Price: £ 7.95


© Micron Radio Control