Uplands House, Castle Howard Road, Malton YO17 6NJ
+44 (0)1653 696008

Deltang Prog3 Receiver Programmer

The Prog3 programmer is used to change settings in Deltang land-based receivers - Rx4 'v5' and Rx6. Each receiver has specific functions that can be configured to alter the way that the receiver responds to R/C commands.

Pins & Plugs

Pins 1-5 on Prog3 represent one row in the programming tables; pin 1 corresponds to the first column, pin 2 the second and so on. Each pin is set individually using the black or red jumper plugs; the black plug makes the LED flashes increase and the red plug decreases the LED flashes.

Inserting either plug briefly will cause the LED to flash the current setting for that pin - insert the plug then remove as soon as the LED starts to flash.

Each pin can be set to 0-18 flashes. Each value is flashed twice. The '0' setting has a very brief flicker. To setup a program:

  1. Switch everything OFF (Prog3, Receivers, Transmitters).
  2. Switch Prog3 ON.
  3. Place a large or small plug on one pin to reveal the setting associated with that pin.
  4. If the plug is kept on the flashes will increase (black plug) or reduce (red plug).
  5. Remove plug to stop the LED flash value changing.
  6. Press the button to save or switch Prog3 off to discard changes.


The button on the side of Prog3 has three functions:

  1. If it is being pressed when Prog3 is switched on, it makes Prog3 start binding.
  2. Once Prog3 is on, when pressed it saves the values associated with each pin. This replaces any values saved previously.
  3. Once Prog3 is on, when pressed it also causes the values associated with each pin to be transmitted to the receiver.
Each time you press the button the values will be saved and transmitted again.


Prog3 needs to be bound to a receiver. Your receiver will still remember the bind info for your proper transmitter, it stores the Prog3 bind information separately so that you can use Prog3 without rebinding. You must not have both Prog3 and your transmitter switched on at the same time.

To bind with Prog3:

  1. Switch everything OFF (Prog3, receivers, transmitters).
  2. Switch the receiver ON and wait ~20s for it to enter bind mode (LED rapid flash).
  3. Press and hold the button on the side of Prog3 and switch it ON. Recevier and Prog2 LEDs should flash slowly.
  4. The receiver LED should display 3-flash (3 flashes followed by a pause and then repeat) if the bind was successful. The Prog3 LED will come on solid.


Prog3 acts as a surrogate transmitter. When Prog3 is ON and the receiver LED show a 3-flash, the receiver is in programming mode. To avoid unintended changes, keep the receiver off while making changes to Prog3 pin flashes.

To make receiver programming changes:

  1. Switch everything OFF (Prog3, receiver, other transmitters).
  2. Switch Prog3 ON and set an appropriate number of LED flashes for each of pins 1-5 to represent one row in the receiver programming table.
  3. Switch one receiver ON and wait for the receiver LED to show 3-flash.
  4. Press the button on Prog3 briefly to save and transmit the changes.
  5. The LED on the receiver flashes fast for 1s if it accepts the changes (no special flash if the values are not accepted).
  6. Switch Prog3 and the receiver OFF before trying to use it with a proper transmitter.
Repeat the steps for each receiver programming row that needs setting.


Receiver Programming Structure

The structure for programming changes are shown on the 'Programming' page for each receiver found using the links below (hosted on the Deltang website). Each output or feature occupies one row in the table. The whole row (up to 5 columns) is programmed at one time. If a column is not used, the number of flashes for that pin on Prog3 can be anything. If one row is used for more than one feature, they must all be set at the same time.

The receiver board ID (eg: 60a) is printed on the PCB.

The version of the software is usually hand-written on the largest black chip on the receiver. If there are more than two numbers, use the first two numbers (top/left).

Version Marking Rx60b Rx61b Rx61c Rx62a Rx63a Rx65a Rx65b
610-x 10x v610
- v610
611-x 11x - - v611
- - v611

Version Marking Rx41d-x-v5 Rx43d-x-v5 Rx45-v5 Rx45-5-v5 Rx45-22-v5
510-x 10x v510
511-x 11x - - - - v511

Version Rx102 Rx105
110-x v110

© Micron Radio Control