Micron R/C will be closed for the Christmas/New Year break from Monday 18th December through Tuesday 2nd January. The last day for posting before Christmas will be Saturday 16th December. Orders may be processed sporadically during the close but we cannot guarantee that any order placed after 4pm on Friday 18th December will be dispatched before Wednesday 3rd January.

DT / DelTang DSM2 Low Voltage Micro Receivers for Land-Based Use

Rx41d-v5 | Rx43d-x-v5 | Rx45 | Rx47-v5 | ADD1 | ADD2 | MAG3 | PROG3 | PROG4

The 'v5' receivers are UK designed and manufactured DSM2 ultra micro 2.4GHz receivers for low voltage (up to 6V) land based applications: cars, boats, and trains. All are compatible with Spektrum DSM2 Air and DSM2 Surface modulation, the Rx47 also supports DSMX. All have a combination of ESC and servo switch outputs which may be programmed to suit your need. Either a stick type transmitter or PROG3 may be used for configuring the receiver settings.

In the receiver descriptions below:

  • H is a reversible H-bridge output,
  • F is a non-reversible output and
  • P is low-current (8mA) servo or switch output.

F outputs can supply up to 2A but the H outputs are lower current. The current capacity of a H output can be boosted and 2 x F outputs can be combined to make an additional H output using one of the add-on amplifier boards: ADD1 for 0.8A and ADD2 for 3A.

The MAG3 magnetic connector board is ideal for making low weight, low force electrical connections.

More information about the DT 'v5' receivers is available on this page. See DSM2 Transmitters for compatible transmitters. Take a look at the Rx6x range of receivers for high voltage (up to 16V).


Click on image for a larger version.
Rx41d-x-v5 DSM2 Micro Receiver with Bi-Directional ESC
(Top | Rx43d-x-v5 | Rx45 | Rx47-v5 | ADD1 | ADD2 | MAG3 | PROG3 | PROG4)

Rx41d-v5 is a DSM2 compatible micro receiver with one 500mA H-bridge reversible ESC output (H), 2 x 2A non-reversible ESC outputs (F) and 3 x servo/switch outputs (P). The H output can be boosted to 0.8A or 3A and the 2 F outputs may be converted to a H. The P outputs may be used to drive servos or used as low current (8mA) switches, e.g for LEDs.

The receiver is available as a bare board with 1.27mm pad space and as a wired version. The latter has lead-out wires installed for battery and motor (H output) and has heat-shrink covering for protection. Please contact us if you need lead-out wires attaching to the F or P outputs.

Rx41d-x-v5
Size:10.1 x 10.3 x 2 mm
Weight:0.28 gm
Outputs:1 x 0.5A H, 2 x 2A F, 3 x P
Features:bare board

Rx41d-x-v5-W
10.1 x 10.3 x 2 mm
0.8 gm
1 x 0.5A H, 2 x 2A F, 3 x P
battery & ESC wiring

The Rx41d-v5 receiver is available in 4 configurations to suit the model usage and type of transmitter:

Rx41d-1-v5Rx41d-2-v5Rx41d-22-v5Rx41d-3-v5
Usage:train with joystick Txtrain with Tx21train with Tx22car with stick-type tx
Motor:low off (ch1)center off (ch1)center off (ch1)center off (ch3)
Direction channel:YesNoNoNo
Selecta:--Enabled-
Instructions:Rx41-1-v5Rx41d-2-v5Rx41d-22-v5Rx41d-3-v5

View the Rx41d-x-v5 programming instructions.

Select type:

Click on image for a larger version.
Rx43d-x-v5 DSM2 Micro Receiver with Bi-Directional ESC
(Top | Rx41d-v5 | Rx45 | Rx47-v5 | ADD1 | ADD2 | MAG3 | PROG3 | PROG4)

Rx43d-x-v5 are a set of DSM2 compatible micro receivers with a combination of H-bridge reversible ESC (H), non-reversible ESC (F) and servo/switch outputs (P). The same PCB and components are used for all variations and the number type of outputs is determined by the loaded firmware.

Rx43d-4-v5 is supplied with ADD1 which must be used for the 4th H output to supply 0.8A. Without the ADD1 connected, the 4th H output can provide only 8mA. Other receivers in the Rx43d-x-v5 range (1, 2 & 3) are not supplied with an ADD1 - ADD1 or ADD2 may be additionally purchased to either increase the current rating of an existing H channel or to convert 2 x F channels into an H channel.

Rx43d-1-v5
Size:11.8 x 12.9 x 2.2 mm
Weight:0.35 gm
Outputs:1 x 0.4A H,
2 x 2A F,
8 x P

Rx43d-2-v5
11.8 x 12.9 x 2.2 mm
0.35 gm
1 x 0.4A H, 1 x 0.8A H,
2 x 2A F,
6 x P

Rx43d-3-v5
11.8 x 12.9 x 2.2 mm
0.35 gm
2 x 0.4A H, 1 x 0.8A H,
2 x 2A F,
4 x P (1 servo, 3 switch)

Rx43d-32-v5
11.8 x 12.9 x 2.2 mm
0.35 gm
2 x 0.4A H, 1 x 0.8A H,
2 x 2A F,
4 x P (4 servos)

Rx43d-4-v5
11.8 x 12.9 x 2.2 mm
0.35 gm
2 x 0.4A H, 2 x 0.8A H,
2 x 2A F,
2 x P

View the user instructions: Rx43d-1-v5, Rx43d-2-v5, Rx43d-3-v5; Rx43d-32-v5; Rx43d-4-v5; and programming instructions.

Select type:

Click on image for a larger version.
Rx45-v5 DSM2 Micro Receiver with Bi-Directional ESC
(Top | Rx41d-v5 | Rx43d-x-v5 | Rx47-v5 | ADD1 | ADD2 | MAG3 | PROG3 | PROG4)

Rx45-v5 is a DSM2 compatible ultra micro receiver with one 500mA H-bridge reversible ESC output (H), 2 x 2A non-reversible ESC outputs (F) and 3 x servo/switch outputs (P). The H output can be boosted to 0.8A or 3A and the 2 F outputs may be converted to a H. The P outputs may be used to drive servos or used as low current (8mA) switches, e.g for LEDs.

Rx45-v5
Size:9.0 x 9.6 x 2.1 mm
Weight:0.24 gm
Outputs:1 x 0.5A H, 2 x 2A F, 6 x P

The Rx45 is available in 3 variants:

  • rx45-car for vehicle control using a stick transmitter
  • rx45-DX3 for vehicle control using a DX3 transmitter
  • rx45-22 for train control using a DT Tx22 transmitter
and with firmware versions:
  • v510: selecta, min motor power, no full-stick throttle option (fwd/rev only)
  • v511: full-stick (low off) throttle option, min motor power not available

View the Rx45-v5 user, programming instructions.

Select type:

Click on image for a larger version.
Rx47-v5 16 chan DSM2/DSMX Micro Receiver with 2 x Bi-Directional ESC
(Top | Rx41d-v5 | Rx43d-x-v5 | Rx45 | ADD1 | ADD2 | MAG3 | PROG3 | PROG4)

Rx47 is a DSM2/DMSX compatible ultra micro receiver with 2 x 800mA H-bridge reversible ESC outputs (H), 2 x 2A non-reversible ESC outputs (F) and 14 x servo/switch outputs (P). The H outputs can be combined to supply 1.6A or mixed for differential steering.

Rx47-v5
Size:17.3 x 10 x 2.5 mm
Weight:0.55 gm
Outputs:2 x 0.8A H, 2 x 2A F, 14 x P
Rx47 user instructions
The Rx47 is available in 5 variants, each of which is a pre-configured set of functions for particular uses.

  • Rx47-1-v5 for vehicle control using a stick transmitter
  • Rx47-2-v5 for trains control using a DT Tx20 or Tx22 transmitter
  • Rx47-22-v5 for train control using a DT Tx22 or Tx24 transmitter
  • Rx47-3-v5 with all P pads configured as servo outputs
  • Rx47-4-v5 for cars
The Rx47 has a rich set of output capabilities. The motor wiring option provides lead-outs for both ESC. Please contact us if you need additional lead-out wires or need ADD1 or ADD2 connecting to provide additional ESC outputs.

Receiver Variant:
Power/Motor Leads:
Heatshink Cover:

There are currently 0 options selected. Click deselect to cancel all option selections.

Base Price: £ 34.00 Total Price: £ 34.00

ADD1 800mA H-Bridge Add-On Board
(Top | Rx41d-v5 | Rx43d-x-v5 | Rx45 | Rx47-v5 | ADD2 | MAG3 | PROG3 | PROG4)

ADD1 is a 4.4mm x 9mm, 0.06gm add-on board for 'v5' receivers to boost H outputs to 0.8A or combine 2 x F outputs to make an additional H output.

Download the ADD1/ADD2 information. Contact us if you need ADD1 wiring to a DT receiver.

£ 4.00

Click on image for a larger version.
ADD2 3A H-Bridge Add-On Board
(Top | Rx41d-v5 | Rx43d-x-v5 | Rx45 | Rx47-v5 | ADD1 | MAG3 | PROG3 | PROG4)

ADD2 is a 6.3mm x 12.5mm, 0.11gm add-on board for 'v5' receivers to boost H outputs to 3A or combine 2 x F outputs to make an additional H output. The supply voltage can be up to 10V, allowing use of a 2S LiPo - in this case, the receiver must be supplied separately as it has a max working voltage of 6V.

Download the ADD1/ADD2 information. Contact us if you need ADD2 wiring to a DT receiver.

£ 7.00

Click on image for a larger version.
MAG3 - 3 Way Magnetic Connectors
(Top | Rx41d-v5 | Rx43d-x-v5 | Rx45 | Rx47-v5 | ADD1 | ADD2 | PROG3 | PROG4)

MAG3 is a pair of 9.5mm sq boards with 3 x 2mm magnets soldered on each. The magnets have good 'holding' strength and act as low weight, low force electrical connectors. Use as servo connector, on/off/charge mechanism, train coupling, etc. (priced for a pair of boards).

£ 12.00

Click on image for a larger version.
Programmer for Rx4x 'v5' and Rx6x Receivers (PROG3)
(Top | Rx41d-v5 | Rx43d-x-v5 | Rx45 | Rx47-v5 | ADD1 | ADD2 | MAG3 | PROG4)

PROG3 is used to change settings in Rx4x 'v5' (from v5.10) and Rx6x (from v6.10) receivers. Changes are made on PROG3 and sent through to the Rx with the push of a button.

All Rx6x receivers can be programmed using a standard DSM2 transmitter - i.e. one with control sticks. The PROG3 is only required for programming if you don't have a standard TX.

Receivers with firmware version at v6.10 and up can be programmed using this programmer. Instructions for using PROG3 are located here.

All current stock has firmware with support for PROG3. Rx6x receivers with firmware older than V6.10 require PROG1 - please contact us if you have a Rx6x receiver with older firmware. If you are unsure of your receiver's firmware version, take a look at the smaller IC package on the circuit board; it will be marked with the 3 version digits - e.g. "6 0 3" for version v6.0.3.

£ 18.00

Click on image for a larger version.
Serial Programmer for Rx4x 'v5' and Rx6x Receivers (PROG4)
(Top | Rx41d-v5 | Rx43d-x-v5 | Rx45 | Rx47-v5 | ADD1 | ADD2 | MAG3 | PROG3)

Prog4 is a programmer for DT land-based receivers (Rx4x-v5 and Rx6x). It is used with a computer to change program settings. Prog4 creates a wireless link between the computer and the receiver. A low-cost serial cable (not included) and freeware file transfer software (not included) are required.

Refer to this page for information on using PROG4.

Suitable PL-2303 USB adapter cables are available from many suppliers. Be aware that many of these do not contain genuine Prolific PL-2303 chips and may result in driver warnings / errors, especially on Windows 10.

£ 18.00

© Micron Radio Control